Belkin Wireless Adapter. Cisco FlipShare TV. Compare Wireless LAN Conceptronic DGET V. B1 Gigabit Ethernet Adapter. DLbased Gigabit Ethernet Adapter generic. DPW Dual Stream Dual-Band Wireless Media Adapter.
Edimax Mbps wireless Edimax Edimax Dual Band Wireless Adapter. Edimax Wi-Fi N Bluetooth4. RouterTech The independent technical support site for all things networking! Skip to content. Quick links. Logout Register. As long as it's router based and doesn't fall into the other categories, this is the place to ask your questions. At the restart, the router didn't give signs of life, and only the Power LED was on On my router there was, or there is , a RouterTech Firmware, so I went here.
I read about firmware upgrade, brick, router repair tool etc Or what is the problem that has my router? Thank you for helping me, and sorry for bad English P. Your firmware is very good and has always worked, compliments. For a bridged connection, the information needed to make and maintain the Internet connection is stored on another computer or gateway device, not in the Modem itself.
In this case, it is not necessary to install software on your computer. It may however be necessary to change some settings in the device, including account information used to identify and verify the connection. All connections to the Internet require a unique global IP address. The IP address can be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required.
DSLT advantages include:. This eliminates the need to reconfigure every host whenever changes in network topology occur.. It is compatible with access servers manufactured by major vendors.
Up to eight Mbps downstream bit rate using the G. Any common web browser software can be used to manage the Modem. The DSLT complies with or is compatible with the following standards as recognized by their respective agencies. Open the shipping carton and carefully remove all items.
In addition to this User's Guide, ascertain that you have:. Place the Modem in a location that permits an easy view of the LED indicators on the front panel. If the indicator lights steady. A solid green light indicates a valid link on startup. This light will blink when. All cable connections to the Modem are made at the rear panel. Connect the power adapter here to power on the Modem. Use the Reset button to restore the settings to the factory default values see Factory Reset Button in the next chapter for instructions on using the reset button.
Place the Modem in a location where it can be connected to the various devices as well as to a power source. The Modem should not be located where it will be exposed to moisture or excessive heat. Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard.
As with any electrical appliance, observe common sense safety procedures. The access point can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.
Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Modem and plug the adapter into a suitable nearby power source. You should see the Power LED indicator light up and remain lit.
The Status LED should light solid green and begin to blink after a few seconds. If this is the first time installing the device, some settings may need to be changed before the Modem can establish a connection. The Modem may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on.
Use a ballpoint or paperclip to gently push down the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings.
The factory default IP address of the Modem is Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Before You Start Please read and make sure you understand all the prerequisites for proper installation of your new Modem. Installation Overview The procedure to install the Modem can be described in general terms in the following steps: 1. Your computer or computers needs to be configured to Obtain an IP address automatically that is, they need to be configured as DHCP clients. The Modem may be reset to its factory default settings by performing a Restore settings operation within the management interface see below.
If you cannot gain access to the management interface, you may opt to use the Reset button on the Note rear panel of the device see Factory Reset Button below. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.
Buy as many as you need. View and download manuals available only for. If you are having trouble installing your driver, you should use the Driver Update Utility for D-Link. It is a software utility that automatically finds, downloads and installs the right driver for your system. You can even backup your drivers before making any changes, and revert back in case there were any problems.
Try it now to safely update all of your drivers in just a few clicks. Once you download and run the utility, it will scan for out-of-date or missing drivers:. When the scan is complete, the driver update utility will display a results page showing which drivers are missing or out-of-date. You can update individual drivers, or all of the necessary drivers with one click. For more help, visit our Driver Support Page for step-by-step videos on how to install drivers for every file type.
Step 1 - Download Your Driver To get the latest driver, including Windows 10 drivers, you can choose from a list of most popular D-Link downloads. D-link dslu driver download.
0コメント